Artykuł COOKIE SONY CAMERA SLEEVE pochodzi z serwisu wingstore.aero.

Currently available for:

• Cookie G4 (New V2 version released April 2024)
• Cookie G3
• Skyhelmets Funjin
• Square1 KiSS Note: See the photo in the images above for the KISS helmet variations. All older KISS helmets have a Large vent, and for awhile the KISS was made with either a Small or Large vent, and now all new KISS helmets have the Small vent. Check your KISS helmet vent size against the photo. Contact us if you have any questions or need help.

The Vmag features extreme magnets while being lightweight. The position of the mount allows the user to see the GoPro recordings while skydiving, also letting you know if it’s recording or not.

Make the best tandem videos! Pull off the camera to make great recordings of your tandem guests as a handheld. You can take photos and video without pulling off your helmet.

The Vmag is easy to attach to your helmet. It comes with two screws to attach the base to the G3, G4 and Kiss. When it’s screwed all the way on, you’re ready to go skydiving!

In case of a linesnag, the magnetic attachment allows you to pull out the the Vmag mount, splitting the mount in two without breaking it, and then simply put it back on again. Or if it’s an emergency entanglement or cutaway, you can throw the camera after pulling it off.

In the event of a collision, or a crash, the Vmag is attached with very strong magnets, and can only be pulled of with a straight forward pull. If the crash force is big enough the mount will release or break.

The cut away is integrated in the mount, so in the event of the camera getting snagged, simply pull off your camera, get clear of the snag, and mount the camera again, so you can keep it.

Simply put the Vmag helmet piece in the air vent and screw it on from the back side. You can attach the Vmag in less than 5 minutes.

Artykuł V-MAG CHIN MOUNT pochodzi z serwisu wingstore.aero.

Works with all GoPro cameras and/or GoPro housings.

This Danish engineered and designed product is a strong magnet mount that works with most of the action camera types on the market. The strong magnets hold the camera securely during your skydive, but it’s then easy to take the V-mount off the helmet mount, with a straight pull. And then it’s extremely easy to put your camera back on again.

In case of a linesnag, the magnetic attachment allows you to pull out the the Vmag mount, splitting the mount in two without breaking it, and then simply put it back on again. Or if it’s an emergency entanglement or cutaway, you can throw the camera after pulling it off.

In the event of a collision, or a crash, the Vmag is attached with very strong magnets, and can only be pulled of with a straight forward pull. If the crash force is big enough the mount will release or break.

The cut away is integrated in the mount, so in the event of the camera getting snagged, simply pull off your camera, get clear of the snag, and mount the camera again, so you can keep it.

Simply put the Vmag helmet piece in the air vent and screw it on from the back side. You can attach the Vmag in less than 5 minutes.

The GoPro arm attachment piece is the same standard arm mount used on the Vmag chin mounts.

Artykuł V-MAG FUEL MOUNT pochodzi z serwisu wingstore.aero.

FEATURES

• Low Power, future compatible, Bluetooth Low Energy (BLE) Camera Indicator
• Intuitive & Standardized Indications: Red for record, Blue for standby, and Yellow for a warning or error.
• Rechargeable battery will last for months on a single charge.
• A slight shake wakes up the device with it’s internal accelerometer. No pressing buttons on the BLU2Pro necessary.

2.5mm input for future enhancements. Currently a switch will start recording, take a single photo, start burst, or activate time-lapse.

Shows catastrophic failures such as no card, camera too hot, no space left, and battery depleted with a flashing yellow.

Indicates wrong mode, battery low, card space minimal, and SD rating check‡ warnings with a flashing yellow when record or standby is active.

Responsive connectivity.*

Artykuł HYPOXIC BLU2PRO pochodzi z serwisu wingstore.aero.

Artykuł CONCEPTUS BITE SWITCH 2,5 mm JACK pochodzi z serwisu wingstore.aero.

Individually tested and guaranteed to function for thousands of shots.

The Tongue Switch is comprises of a 1/2″ pressure-sensitive switch mechanism, a 1″ flattened and bite-resistant stem, a 36″ coaxial wire, and a digital plug with a 90 degree elbow bend. It is configured so that the pressure-sensitive switch face is always oriented towards the user’s tongue, regardless of the direction of insertion into the mouth, thus allowing the wire to be routed to the left or the right.

The Conceptus Tongue Switch is ready-to-use with most Canon cameras and can be adapted to almost any camera with a remote shutter release jack. It’s easy to connect and disconnect from your camera, and can be easily spit out at the end of the dive or if you need to cut away your headgear.

Similar to the Bite Switch except this is controlled by your tongue. The Tongue Switch works with even the tightest full-face headgear and chin cups, and requires no jaw movement or blowing. It is operated by a movement similar to pressing your tongue against the front teeth.

It measures 23″ long, switch body is 1/2″ wide. (If you need a 2.5 plug see item L1334.)

Artykuł CONCEPTUS TONGUE SWITCH DIGITAL PLUG 3 PIN pochodzi z serwisu wingstore.aero.

Artykuł CONCEPTUS TONGUE SWITCH 2,5 mm JACK pochodzi z serwisu wingstore.aero.

This switch fits comfortably in your mouth, is extremely easy to use, and will take one or multiple exposures. They’re perfect for freeflyers and anyone wanting hands-free photography without jumpsuit circuitry. The Bite Switch works best with open-faced headgear.

Individually tested and guaranteed to function for thousands of shots. The design has been tested up to 3000 bites without a malfunction, and none have failed in the field when used properly.

The Conceptus Bite Switch is ready-to-use with most Canon cameras and can be adapted to almost any camera with a remote shutter release jack. It’s easy to connect and disconnect from your camera, and can be easily spit out at the end of the dive or if you need to cut away your headgear.

It measures 23″ long, switch body is 1/4″ diameter.

The Conceptus Bite switch with Canon digital plug is compatible with many of the Canon series of digital cameras, such as the EOS 1D, 5D, 10D, 20D, 30D and 40D.

This is a mouth-operated, totally electronic shutter releases for use with any still camera with a remote shutter release jack. The switch plugs directly into the camera without need for a separate switch module. The design is securely sealed and waterproof. Since the switch is mouth-operated, it does not interfere with grips on exits or in freefall, or with canopy deployment, control and emergency procedures.

This switch is designed to work with the following Canon models:

Canon EOS 7D / Canon EOS 1V / Canon EOS 3 / Canon EOS 1D / Canon EOS 1DS / Canon EOS 1DS MARK II / EOS 1DS MARK IV / Canon EOS 10D / Canon EOS 20D / Canon EOS 30D / Canon EOS 40D / Canon EOS 5D/ Canon EOS D30 / Canon EOS D60

Artykuł CONCEPTUS BITE SWITCH 2,5 mm DIGITAL PLUG 3 PIN pochodzi z serwisu wingstore.aero.

Artykuł WINGSTORE HELMET CAMERA MOUNT pochodzi z serwisu wingstore.aero.

Artykuł V-MAG STANDARD ARM pochodzi z serwisu wingstore.aero.